Progress Sway Bar

***calircr*** · 11-28-2006, 04:28 PM

Hey Everyone,

I was just wondering...after installing the sway bar, do I need to get an alignment done or will the install not mess with the alignment at all.

Thanks in advance

kdb · 11-28-2006, 04:30 PM

It wont mess with your alignment. It's a really simple install actually.

***rippars*** · 11-28-2006, 04:33 PM

nope... just make sure you gease up the bushings really good.

fa1 · 11-28-2006, 10:08 PM

I'd recommend some beefier endlinks also.

slimjim8481 · 12-08-2006, 10:04 AM

I am putting a si sway bar on my lx. I have heard that you dont grease the rubber bushings when you install the new bar. Is that corect?

**Nomar06** · 12-08-2006, 01:10 PM

Always grease bushings, if not they squeek!!!

bhoy · 12-08-2006, 01:15 PM

for rubber bushings you don't need to grease it but for urethane ones you do.

si_civic · 12-15-2006, 10:56 AM

What's wrong with a little squeaking?

Off topic, but we have a 100km/h+ wind warning and its blowing snow like a MOFO... woooow....

Anywho, very important to grease those bushes up.

11-28-2006, 04:28 PM	#1 (permalink)
*calircr* Giants, GO! Join Date: Nov 2005 Location: San Diego Posts: 1,509 iTrader: 5 / 100%	Progress Sway Bar Hey Everyone, I was just wondering...after installing the sway bar, do I need to get an alignment done or will the install not mess with the alignment at all. Thanks in advance __________________ "Porto-Potty Splash back is Gross!"

12-08-2006, 01:10 PM	#6 (permalink)
Nomar06 I haz da Taffy's Join Date: Jul 2006 Location: Charlotte, NC Age: 27 Posts: 21,800 iTrader: 4 / 100%	Always grease bushings, if not they squeek!!! __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
noise from rear... hfp suspension and progress rear sway bar	rippars	Mechanical Problems & Technical Chat	8	07-01-2008 08:42 PM
Progress rear sway bar and stock endlinks	pengful	CorSport	16	04-04-2007 02:25 PM
Progress rear sway bar still on backorder?	Michael Bolton	CorSport	13	11-21-2006 02:24 PM
Ordered a Progress Technology rear sway bar	Cookstar	Suspension and Brakes	22	06-16-2006 02:08 AM
Progress Sway Bar	johnai3	Suspension and Brakes	2	05-22-2006 12:08 PM

11-28-2006, 04:30 PM	#2 (permalink)
kdb Member Join Date: Aug 2006 Location: Santa Clara, Ca Posts: 34 iTrader: 0 / 0%	It wont mess with your alignment. It's a really simple install actually.

11-28-2006, 10:08 PM	#4 (permalink)
fa1 Senior Member Join Date: May 2006 Location: SF, CA Age: 19 Posts: 2,418 FA Squad Member #17 iTrader: 1 / 100%	I'd recommend some beefier endlinks also.

12-08-2006, 10:04 AM	#5 (permalink)
slimjim8481 Member Join Date: Nov 2006 Location: Jax, FL Posts: 63 James iTrader: 4 / 100%	I am putting a si sway bar on my lx. I have heard that you dont grease the rubber bushings when you install the new bar. Is that corect?

12-08-2006, 01:15 PM	#7 (permalink)
bhoy Senior Member Join Date: Apr 2006 Location: NJ Age: 41 Posts: 774 Marv iTrader: 7 / 100%	for rubber bushings you don't need to grease it but for urethane ones you do.

12-15-2006, 10:56 AM	#8 (permalink)
si_civic Senior Member Join Date: Jul 2006 Location: B.C. ,Canada Age: 30 Posts: 4,608 A/Cst.D.F.Abate iTrader: 10 / 100%	What's wrong with a little squeaking? Off topic, but we have a 100km/h+ wind warning and its blowing snow like a MOFO... woooow.... Anywho, very important to grease those bushes up.